Looking for the best Gas Piston System. Look no further! Black Rifle Arms has developed the most innovated Gas Piston Systems, best bolt carrier groups, enhanced firing pins, extended firing pins, gas piston, piston, piston uppers, 300BLK Piston Uppers

AR-15 / M16 7.62x39 Extractor Kit

3 Review(s) Write a Review

Your Price: $24.99

Questions about this item? Ask here.

Part Number: 2010015

Availability: In Stock

Quantity

Description
Customer Reviews
Questions and Answers
Disclaimers

AR15/M16 7.62x39 Extractor Kit

For Use with Bolt Assemblies with a .125" Bolt Face Recess
Extractor machined from MIL-S5000 Steel and Vacuum Hardened
Extractor Pin
Extractor Spring/Rubber Insert
O-Ring
Phosphate Finish

PLEASE NOTE:

Our 7.62x39 Extractor DO NOT work with Bear Creek Arsenal Bolt Assemblies
We DO NOT carry Melonited Extractors As They Are Subject to Brittleness

Rating Snapshot

Select a row below to filter reviews.

Average Customer Ratings

5.0

This is the most heavy duty 7.62x39 extractor I have found. I ordered 2. 1 to replace a broken extractor and 1 as a backup. (I don't think I'm going to need it).

Reviewed by: Tracy from Las Vegas on 4/8/2017

Thank you

Was having issues with breaking extractors from various retailers, contacted BRA and they stated premature failures can be due to heat treat issues and/or overgassing. Suggested a h2 buffer which would slow bcg down allowing for casing time to shrink before extracting round. Had an H2 buffer on hand and purchased extractor and so far so good. Took me a few months to followup s I wanted to see how things would go. Thank you for taking the time to explain things to me.

Reviewed by: David from Ohio on 11/18/2017

Mr.

Easily replaced my broken extractor with this, holds up well so far.

Reviewed by: Jack from Missouri on 5/12/2017

View all Q&A

Q: Will this extractor work for 7.62x39 ARAK-21? The extractor broke on my upper and I need a replacement for it. Checked with Faxon so far no response. Please advise.

Asked by: Joe - 11/10/2025

A: According to Faxon it should work with no issues. This is Faxon verbiage per their product website for the ARAK-21® Features: "The firing pin, extractor spring, and ejector spring are the only parts that are standard and interchangeable with an AR-15 upper receiver."

Answer provided by: Administrator (11/11/2025)

Q: Will this work with a maxim pdx chambered in 762x39?

Asked by: Corey - 10/23/2025

A: It should, we only know of BCA having issues and that's due to BCA having been all over the board with specc's.

Answer provided by: Administrator (10/24/2025)

Q: Will the ar15 7.62x39 extractor kit fit in my psa ks47 hybrid bolt.

Asked by: Tom shaw - 6/28/2025

A: Several of our customers use our 7.62x39 extractors for their PSA KS47; however, they have reported their KS47 are overgassed which puts undue stress on the extractors.

Answer provided by: Administrator (7/18/2025)

Q: Why does this say it's not for BCA 7.62 bokt face. I just check the bolt face depth for the 7.62x39 BCA bolt and it's .125" ? So what gives on this ?

Asked by: Steven Andrews - 6/2/2025

A: They have been all over the place with specs, so it was just easier to state it won't work.

Answer provided by: Administrator (6/23/2025)

Q: Will this extractor work in a leadstar ar10?

Asked by: Gordon - 6/1/2025

A: No these extractors are for an AR15 7.62x39, what you would need is an AR-10/.308/7.62x51.

Answer provided by: Administrator (6/1/2025)

Q: Work with nickel boron coated bolt? Is it stronger then most to not break after 450rds?

Asked by: Frank - 5/25/2025

A: We don't have issues with bolts breaking, what usually fail after awhile is the extractor and that is due to the thinness of the extractor lips.

Answer provided by: Administrator (6/1/2025)

Q: is this extractor arm a stronger steel than the average mil-spec?

Asked by: Aaron - 4/2/2025

A: Extractor Produced from MIL-S-5000 Steel, Vacuum Hardened, Machined

Answer provided by: Administrator (4/13/2025)

Q: Will this work on a Diamondback ar47 bolt

Asked by: Kino - 3/31/2025

A: If your Diamondback AR47 utilizes a standard 7.62x39 Extractor it will work fine. Our extractors work fine with PSA AR47 with no issues.

Answer provided by: Administrator (4/13/2025)

Q: Will this extractor work in a radical arms AR?

Asked by: John Melton - 1/26/2025

A: Should work just fine with Radical, we have never received reports of non-compatibility with them.

Answer provided by: Administrator (2/21/2025)

Q: Will this extractor work with the Radical Firearms AR762? That is chambered in 762x39 but I don’t wanna buy something unless I know it’s compatible.

Asked by: Gabriel - 12/10/2024

A: Should fit fine, we have customers that buy them for their Radical 7.62x39.

Answer provided by: Administrator (12/12/2024)

Questions about this item? Ask here.

Magpul Industries MS1 1 or 2 Point Sling

$39.95

In Stock

Add to Wish List

Select Options

Strike Industries Link Curved Foregrip for MLOK and Keymod

In Stock

Add to Wish List

Select Options

Black Rifle Arms AR-9mm Handguard Screws

$1.00

Out of Stock

Add to Wish List

Add To Cart

LaRue Tactical MBT-2S Trigger

$115.00

Out of Stock

Add to Wish List

Add To Cart

Black Rifle Arms Bolt Carrier Adapter for Sylvan Arms Folder Stock

$20.00

In Stock

Add to Wish List

Add To Cart

Trijicon, Tenmile 4.5-30x56mm SFP Long-Range Riflescope with Red/Green MOA Long Range, 34mm Tube, Matte Black, Exposed Elevation Adjuster with Return to Zero Feature

$2,912.00

In Stock

Add to Wish List

Add To Cart

[history_item_name]

[ITEMPRICE] ~~[ITEMPRICE] Original price~~ [ITEMSALEPRICE] Sale

Clear

AR-15 / M16 7.62x39 Extractor Kit

Average Customer Ratings

Related Items

Recently Viewed Items

AR-15 / M16 7.62x39 Extractor Kit

Related Items

Recently Viewed Items

Mailing List